Stanley jumpit manual: how to use stanley jumpit 1000? - Everstart Jump Starter (2024)

Stanley JumpIt manual on how to use this jump starter is here to check. A Stanley JumpIt 1000is a powerful jump starter that is perfect for anyone who needs a reliable source of power when they’re out and about. This jump starter is lightweight and easy to use, so you can get started quickly. Plus, it has a large battery capacity so you can get your vehicle started quickly and easily.

Stanley jumpit 1000 amp jump starter

The Stanley Jumpit 1000 jump starter is a small, portable device that can start your car’s engine when the battery dies. It has enough power to start a regular gasoline engine several times before it needs recharging. The Jumpit 1000 is made by the Stanley Black & Decker company, the same manufacturer that makes many household tools and garage products, including toolboxes and hand held power tools.

Download Stanley jumpit mANUAL

No need to waste time for searching online, you can directly download the official Stanley jumpit jump starter user manual from here.

How to use stanley jumpit 1000?

How do I use the Stanley 1000 Amp Jump Starter?

Step 1:

To use the Stanley 1000 Amp Jump Starter, you need to first switch on the power. The power switch is located towards the bottom of the unit and it is indicated by a LED light. When it is switched on, the LED light will illuminate and you’re ready to go!

Step 2:

The next step is making sure your battery terminals are clean. You need to first switch on the power. The power switch is located towards the bottom of the unit and it is indicated by a LED light. When it is switched on, the LED light will illuminate and you’re ready to go!

Step 3:

The next step is making sure your battery terminals are clean. The red clamps are positive (+) and the black clamps are negative (-). Connecting them to dirty terminals might cause sparks which can result in potential safety hazards. To avoid this, you should clean your car battery terminals before you jump start your vehicle. To connect the Stanley jump starter to your car battery all you need to do is place both red clamps on the positive terminal (+) and place both black clamps on the negative terminal (-).

Step 4:

Once connected correctly, try starting your vehicle. If this does not work, then check if: Your clamp connections are correct (red goes with + and black goes with -); You have sufficient charge in your jump starter (the 4 LED lights will indicate how much charge you have); or Your car battery needs replacing.

How to charge stanley jumpit 1000?

1. Before attempting to charge your Stanley Jumpit 1000 jump starter, be sure to read all instructions and warnings in the included Owner’s Manual.

2. To charge the unit, first connect the included AC charger to the charging port on the side of the jump starter.

3. Then plug the AC charger into a wall outlet. The charging indicator light on the unit will turn red, indicating that the unit is charging.

4. Once the unit is fully charged, the charging indicator light will turn green. At this point, you can unplug the AC charger and begin using the unit.

Tips for using The Jump Starters

Stanley jumpit manual: how to use stanley jumpit 1000? - Everstart Jump Starter (1)

Check The Stanley jumpit Functions

Here are some tips for using the Stanley jumpit 1000:

To start your vehicle with the Stanley Jumpit 1000, connect the red positive clamp first to the positive terminal on the car’s battery and then connect the black negative clamp to any unpainted metallic surface on the engine block.

Once connected correctly, press the “power” button on the unit to start it. To charge your devices with this portable power pack, hold down the “power” button for 2 seconds until you see a blue light coming up from behind panel next to “USB” output port. This indicates that it is ready to accept any device that uses USB charging cable (the same one you use for charging your smartphone or tablet).

Stanley jumpit 1000 has a multi-functional LED light with a flashlight and a red emergency light that can be used as a signal in an emergency. It is powered by a 12V battery with a capacity of 18Ah that can be charged at home using an AC adapter or at the gas station using a DC charger. This tool is built with high-impact casing that is durable and ideal for all weather conditions.

Why is stanley jumpit 1000 not charging and how to fix?

If your Stanley Jumpit 1000 jump starter is not charging, there are a few things you can do to try and fix the issue.

  1. First, check the power cord to make sure it is firmly plugged into the jump starter and into an outlet.
  2. Next, check the connections on the battery. If the connections are loose, try tightening them. If the battery is damaged, you may need to replace it.
  3. Finally, if the jump starter is still not charging, you may need to take it to a professional for further diagnosis.

Stanley jumpit manual: how to use stanley jumpit 1000? - Everstart Jump Starter (2)

Know More Stanley jumpit Features

Summary

The manual that comes with your jump starter kit should explain everything in detail, check our article to get to know all about using the Stanley Jumpit 1000 jump starter.

Contents show

Stanley jumpit manual: how to use stanley jumpit 1000? - Everstart Jump Starter (2024)
Top Articles
Latest Posts
Article information

Author: Delena Feil

Last Updated:

Views: 5905

Rating: 4.4 / 5 (65 voted)

Reviews: 80% of readers found this page helpful

Author information

Name: Delena Feil

Birthday: 1998-08-29

Address: 747 Lubowitz Run, Sidmouth, HI 90646-5543

Phone: +99513241752844

Job: Design Supervisor

Hobby: Digital arts, Lacemaking, Air sports, Running, Scouting, Shooting, Puzzles

Introduction: My name is Delena Feil, I am a clean, splendid, calm, fancy, jolly, bright, faithful person who loves writing and wants to share my knowledge and understanding with you.